DIY LEGO Table Tutorial

posted in: DIY, LEGO | 0

Post contains affiliate links.Step-by-step instructions for converting an old table into a DIY LEGO table.Our kids are obsessed with LEGO. This is an obsession that we have gladly fed over the years. For  Mordecai’s 14th birthday, we decided to convert an old table into a LEGO table for him. Here I will show you step-by-step how transformed a preschool table into a workable LEGO table. 

DIY LEGO Table Tutorial

1. Start with a table.

This is a thirteen year old Lakeshore table (similar to this), but you could just as easily use one you already have or pick one up at the consignment store or a garage sale. Our table has been used by over a dozen kids for the last 13 years…but it was time for an upgrade.

Step-by-step instructions for converting an old table into a DIY LEGO table.

Two year old Hezekiah at busy working at the table.

2. Strip the table.

This ended up being more work than I anticipated. Our table was covered with a laminate top. One corner had come off of the table years ago, so I thought it would be a simple job to just pop off the rest. I was wrong. It took Enoch heating the table with a propane torch and prying it up to remove it. This step probably took about an hour.

Step-by-step instructions for converting an old table into a DIY LEGO table.

3. Plan you layout.

I ordered the base plates from Amazon (listed below). Chuck, Enoch and I moved the pieces here and there to get this just as we wanted. Notice, the water, then sand, then grass…aren’t we creative?

Step-by-step instructions for converting an old table into a DIY LEGO table.

4. Cut the pieces.

Once we had the layout the way we wanted, Chuck went to work cutting the pieces to size. He used a Bosch variable speed grinder to cut the LEGO baseplates. The variable speed was important to get a smooth, even cut. Chuck was able to slow the grinding down in order to have more control. 

[For our table we used: 3 15×15″ gray baseplates, two 10×10  sand colored baseplates, 3 10×10 green base plates and one 10×10 blue baseplate. Amazon would only let us by two of any given baseplate, so to get the right number of plates, I order this education set.]

Step-by-step instructions for converting an old table into a DIY LEGO table.

Step-by-step instructions for converting an old table into a DIY LEGO table.

Next he used the side of the grinder to smooth the edges out.

Step-by-step instructions for converting an old table into a DIY LEGO table.

Step-by-step instructions for converting an old table into a DIY LEGO table.

Chuck used his fingers to pick off the loose plastic, for a smooth, straight edge.

Step-by-step instructions for converting an old table into a DIY LEGO table.

Step-by-step instructions for converting an old table into a DIY LEGO table.

For the corners, he literally just drew the curve with a permanent marker, then carefully cut with the grinder.

Step-by-step instructions for converting an old table into a DIY LEGO table. Step-by-step instructions for converting an old table into a DIY LEGO table.

5. Connect the LEGO baseplates with LEGO bricks.

This step is of absolute importance. Do not skip this! Initially Chuck wanted to make sure that there was no space between the baseplates, pressing them as close together as possible. I suggested we get some bricks and make sure they fit together. As it turns out a bit of space was needed. Think about it: with LEGO, if the alignment is off by even a hair you will not be able to connect the bricks at the seam between two baseplates.

We ended up connecting each and every baseplate to make sure they were aligned properly.

Step-by-step instructions for converting an old table into a DIY LEGO table.

Step-by-step instructions for converting an old table into a DIY LEGO table.

6. Lightly sandpaper the surface to prep for gluing.

This only took a minute or two and Enoch did it by hand. We just wanted to make sure the surface was clear of debris.

Step-by-step instructions for converting an old table into a DIY LEGO table.

7. Apply cement.

We used Welwood Original Contact Cement. Chuck poured it on and then used an 8″ putty knife to spread it on evenly. He took special care around the edges so the baseplates wouldn’t peel off.

Step-by-step instructions for converting an old table into a DIY LEGO table.

Step-by-step instructions for converting an old table into a DIY LEGO table.

Step-by-step instructions for converting an old table into a DIY LEGO table.

8. Place the pre-cut baseplates.

Now it gets fun! Take the baseplates that you already cut and place them one by one on the table. We left them connected with the LEGO bricks while Chuck spread the cement. Enoch removed one plate at a time and handed them to Chuck. Within minutes the pieces were placed and glued. We then reconnected them with LEGO bricks to double check the alignment.

Step-by-step instructions for converting an old table into a DIY LEGO table.

Step-by-step instructions for converting an old table into a DIY LEGO table.

Step-by-step instructions for converting an old table into a DIY LEGO table.

9. Clamp and leave overnight. 

The contact cement is supposed to seal on contact. We chose to clamp the table and leave it overnight. The next morning, the table was finished! 

Step-by-step instructions for converting an old table into a DIY LEGO table. Step-by-step instructions for converting an old table into a DIY LEGO table.

I couldn’t even manage to get pictures before Mordecai was moving his creations onto it.

Love the idea? Be sure and check out more of my LEGO posts (check the drop down category box in the sidebar.)

Facebook Comments

Please share your thoughts!